Vehicles
Sections
48 not categorized PORSCHE 356 B SEAL ENGINECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 (includes uncategorized and accessory items) 91150411102 This one-piece seal is closest to the rear bumper, we recommend replacing this when removing the motor for maintenance. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. We recommend replacing both the small and large engine seals, the small is part # 91150411302 sold individually. 1 necessary per car. Please note: this only fits 3.0l 930 turbo models from 1975-77. 930 3.3l models require part # 93050417001 View/Change Diagram
From $45.29
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
From $14.00
Make a selection 99610090394 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$632.50
Make a selection 90150179720 Known as: profile rail View/Change Diagram
From $70.54
Make a selection 91150493000 Known as: strap View/Change Diagram
From $24.23
Make a selection 91150411302EQ This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.
$16.50
Make a selection
$23.10
Make a selection 99610090391 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$808.50
Make a selection
$40.91
Make a selection 99970711341 Note: only for o.e. Type steel tubes. View/Change Diagram
From $1.00
Make a selection
$44.58
Make a selection
$123.30
Make a selection 00004301000 View/Change Diagram
From $38.00
Make a selection
$12.54
Make a selection 9997071124A Oil return tube o-ring for genuine oil tube. Will not work on aftermarket tubes. Sold individually. View/Change Diagram
From $1.35
Make a selection TL1021 This universal flywheel lock has been designed for use on all air-cooled Porsche engines (series 356, 912, 914 & all 911s through 1969) and on all air-cooled volkswagen engines (type 1,2,3 & 4). This tool is a must when changing a flywheel or its seal and it comes in handy when changing a clutch. Made from a forging, this quality tool will last a lifetime. Gpcg91101000. General Fitment914 1970-76356 1950-59 356 1960-65 912 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$12.00
Make a selection 021119955 This is another one of those small sealing washers to insure that all of the cooling air is flowing over the engine and not out the open holes! order all of the other sealing washers at the same time like the spark plugs and the oil pressure switch grommet. View/Change Diagram
$5.25
Make a selection 021115487 Cork gasket that fits inbetween the oil filler and the engine case on all 914 four cylinder models. critical on 1.8 models to help seal vacuum leaks as well as oil leaks. View/Change Diagram
From $2.90
Make a selection 93010090104EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your engine case (short block). Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. Please note: if you prefer the genuine crankshaft sealing ring, please order part # 99911342641 this also includes the intermediate shaft o-ring, part # 99970731540. Please check the model fitment tab to ensure accurate fitment.
$118.80
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 039129707 This is the intake block that fits in between the intake runner pipes and the head. critical for insulating the injectors from engine head and for sealing the intake system from vacuum leaks! Two required per car. View/Change Diagram
From $9.50
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection 91150411500 This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car. View/Change Diagram
From $52.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |